# wlctl
Usage: wlctl [-a|i <adapter>] [-h] [-d|u|x] <command> [arguments]

  -h        this message and command descriptions
  -h [cmd]  command description for cmd
  -a, -i    adapter name or number
  -d        output format signed integer
  -u        output format unsigned integer
  -x        output format hexdecimal

ver     get version information

cmds    generate a short list of available commands

up      reinitialize and mark adapter up (operational)

down    reset and mark adapter down (disabled)

out     mark adapter down but do not reset hardware(disabled)
        On dualband cards, cards must be bandlocked before use.

clk     set board clock state. return error for set_clk attempt if the driver is not down
        0: clock off
        1: clock on

restart Restart driver.  Driver must already be down.

reboot  Reboot platform

radio   Set the radio on or off.
        "on" or "off"

dump    Give suboption "list" to list various suboptions

srclear Clear the srom

srdump  print contents of SPROM to stdout

srwrite Write the srom: srwrite byteoffset value

nvram_dump
        print nvram variables to stdout

nvset   set an nvram variable
        name=value (no spaces around '=')

nvget   get the value of an nvram variable

nvram_get
        get the value of an nvram variable

revinfo get hardware revision information

msglevel
        set driver console debugging message bitvector
        type 'wl msglevel ?' for values

PM      set driver power management mode:
        0: CAM (constantly awake)
        1: PS  (power-save)
        2: FAST PS mode

wake    set driver power-save mode sleep state:
        0: core-managed
        1: awake

promisc set promiscuous mode ethernet address reception
        0 - disable
        1 - enable

monitor set monitor mode
        0 - disable
        1 - enable active monitor mode (interface still operates)

frag    Deprecated. Use fragthresh.

rts     Deprecated. Use rtsthresh.

cwmin   Set the cwmin.  (integer [1, 255])

cwmax   Set the cwmax.  (integer [256, 2047])

srl     Set the short retry limit.  (integer [1, 255])

lrl     Set the long retry limit.  (integer [1, 255])

rate    force a fixed rate:
        valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
        valid values for 802.11b are (1, 2, 5.5, 11)
        valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate

mrate   force a fixed multicast rate:
        valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
        valid values for 802.11b are (1, 2, 5.5, 11)
        valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate

a_rate  force a fixed rate for the A PHY:
        valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate

a_mrate force a fixed multicast rate for the A PHY:
        valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate

bg_rate force a fixed rate for the B/G PHY:
        valid values for 802.11b are (1, 2, 5.5, 11)
        valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate

bg_mrate
        force a fixed multicast rate for the B/G PHY:
        valid values for 802.11b are (1, 2, 5.5, 11)
        valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate

infra   Set Infrastructure mode: 0 (IBSS) or 1 (Infra BSS)

ap      Set AP mode: 0 (STA) or 1 (AP)

bssid   Get the BSSID value, error if STA and not associated

bssmax  get number of BSSes

channel Set the channel:
        valid channels for 802.11b/g (2.4GHz band) are 1 through 14
        valid channels for 802.11a  (5 GHz band) are:
                36, 40, 44, 48, 52, 56, 60, 64,
                100, 104, 108, 112, 116,120, 124, 128, 132, 136, 140,
                149, 153, 157, 161,
                184, 188, 192, 196, 200, 204, 208, 212, 216

cur_mcsset
        Get the current mcs set

chanspecs
        Get all the valid chanspecs (default: all within current locale):
        -b band (5(a) or 2(b/g))
        -w bandwidth, 10,20 or 40
        [-c country_abbrev]


chanspec
        Set <channel>[a,b][n][u,l]
        channel number (0-224)
        band a=5G, b=2G, default to 2G if channel <= 14
        bandwidth, n=10, non for 20 & 40
        ctl sideband, l=lower, u=upper
OR Set channel with legacy format:
        -c channel number (0-224)
        -b band (5(a) or 2(b/g))
        -w bandwidth, 10,20 or 40
        -s ctl sideband, -1=lower, 0=none, 1=upper

dfs_channel_forced
        Set <channel>[a,b][n][u,l]
        channel number (0-224)
        band a=5G, b=2G, default to 2G if channel <= 14
        bandwidth, n=10, non for 20 & 40
        ctl sideband, l=lower, u=upper


tssi    Get the tssi value from radio

txpwr   Set tx power in milliwatts.  Range [1, 84].

txpwr1  Set tx power in in various units. Choose one of (default: dbm):
        -d dbm units
        -q quarter dbm units
        -m milliwatt units
Can be combined with:
        -o turn on override to disable regulatory and other limitations
Use wl txpwr -1 to restore defaults

txpathpwr
        Turn the tx path power on or off on 2050 radios

txpwrlimit
        Return current tx power limit

powerindex
        Set the transmit power for A band(0-63).
        -1 - default value

atten   Set the transmit attenuation for B band. Args: bb radio txctl1.
        auto to revert to automatic control
        manual to supspend automatic control

phyreg  Get/Set a phy register:
        offset [ value ] [ band ]

radioreg
        Get/Set a radio register:
        offset [ value ] [ band ]

ucflags Get/Set ucode flags 1, 2, 3(16 bits each)
        offset [ value ] [ band ]

shmem   Get/Set a shared memory location:
        offset [ value ] [band ]

macreg  Get/Set any mac registers(include IHR and SB):
        macreg offset size[2,4] [ value ] [ band ]

ucantdiv
        Enable/disable ucode antenna diversity (1/0 or on/off)

gpioout Set any GPIO pins to any value. Use with caution as GPIOs would be assigned to chipcommon
        Usage: gpiomask gpioval

ampdu_tid
        enable/disable per-tid ampdu; usage: wl ampdu_tid <tid> [0/1]

ampdu_send_addba
        send addba to specified ea-tid; usage: wl ampdu_send_addba <tid> <ea>

ampdu_send_delba
        send delba to specified ea-tid; usage: wl ampdu_send_delba <tid> <ea>

ampdu_clear_dump
        clear ampdu counters

dpt_deny
        adds/removes ea to dpt deny list
        usage: wl dpt_deny <ea> <add,remove>


dpt_endpoint
        creates/updates/deletes dpt endpoint for ea
        usage: wl dpt_endpoint <create, update, delete> <ea>


antdiv  Set antenna diversity for rx
        0 - force use of antenna 0
        1 - force use of antenna 1
        3 - automatic selection of antenna diversity

txant   Set the transmit antenna
        0 - force use of antenna 0
        1 - force use of antenna 1
        3 - use the RX antenna selection that was in force during
            the most recently received good PLCP header

plcphdr Set the plcp header.
        "long" or "auto" or "debug"

phytype Get phy type

rateparam
        set driver rate selection tunables
        arg 1: tunable id
        arg 2: tunable value

wepstatus
        Set or Get WEP status
        wepstatus [on|off]

primary_key
        Set or get index of primary key

addwep  Set an encryption key.  The key must be 5, 13 or 16 bytes long, or
        10, 26, 32, or 64 hex digits long.  The encryption algorithm is
        automatically selected based on the key size. keytype is accepted
        only when key length is 16 bytes/32 hex digits and specifies
        whether AES-OCB or AES-CCM encryption is used. Default is ccm.
        addwep <keyindex> <keydata> [ocb | ccm] [notx] [xx:xx:xx:xx:xx:xx]

rmwep   Remove the encryption key at the specified key index.

keys    Prints a list of the current WEP keys

tsc     Print Tx Sequence Couter for key at specified key index.

wsec_test
        Generate wsec errors
        wsec_test <test_type> <keyindex|xx:xx:xx:xx:xx:xx>
        type 'wl wsec_test ?' for test_types

tkip_countermeasures
        Enable or disable TKIP countermeasures (TKIP-enabled AP only)
        0 - disable
        1 - enable

wsec_restrict
        Drop unencrypted packets if WSEC is enabled
        0 - disable
        1 - enable

eap     restrict traffic to 802.1X packets until 802.1X authorization succeeds
        0 - disable
        1 - enable

cur_etheraddr
        Get/set the current hw address

authorize
        restrict traffic to 802.1X packets until 802.1X authorization succeeds

deauthorize
        do not restrict traffic to 802.1X packets until 802.1X authorization succeeds

deauthenticate
        deauthenticate a STA from the AP with optional reason code (AP ONLY)

wsec    wireless security bit vector
        1 - WEP enabled
        2 - TKIP enabled
        4 - AES enabled
        8 - WSEC in software
        0x80 - FIPS enabled

auth    set/get 802.11 authentication type. 0 = OpenSystem, 1= SharedKey

wpa_auth
        Bitvector of WPA authorization modes:
        1       WPA-NONE
        2       WPA-802.1X/WPA-Professional
        4       WPA-PSK/WPA-Personal
        64      WPA2-802.1X/WPA2-Professional
        128     WPA2-PSK/WPA2-Personal
        0       disable WPA

wpa_cap set/get 802.11i RSN capabilities

set_pmk Set passphrase for PMK in driver-resident supplicant.

scan    Initiate a scan.
        Default an active scan across all channels for any SSID.
        Optional arg: SSID, the SSID to scan.
        Options:
        -s S, --ssid=S          SSID to scan
        -t ST, --scan_type=ST   [active|passive] scan type
        --bss_type=BT           [bss/infra|ibss/adhoc] bss type to scan
        -b MAC, --bssid=MAC     particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
        -n N, --nprobes=N       number of probes per scanned channel
        -a N, --active=N        dwell time per channel for active scanning
        -p N, --passive=N       dwell time per channel for passive scanning
        -h N, --home=N          dwell time for the home channel between channel scans
        -c L, --channels=L      comma or space separated list of channels to scan

iscan_s Initiate an incremental scan.
        Default an active scan across all channels for any SSID.
        Optional arg: SSID, the SSID to scan.
        Options:
        -s S, --ssid=S          SSID to scan
        -t ST, --scan_type=ST   [active|passive] scan type
        --bss_type=BT           [bss/infra|ibss/adhoc] bss type to scan
        -b MAC, --bssid=MAC     particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
        -n N, --nprobes=N       number of probes per scanned channel
        -a N, --active=N        dwell time per channel for active scanning
        -p N, --passive=N       dwell time per channel for passive scanning
        -h N, --home=N          dwell time for the home channel between channel scans
        -c L, --channels=L      comma or space separated list of channels to scan

iscan_c Continue an incremental scan.
        Default an active scan across all channels for any SSID.
        Optional arg: SSID, the SSID to scan.
        Options:
        -s S, --ssid=S          SSID to scan
        -t ST, --scan_type=ST   [active|passive] scan type
        --bss_type=BT           [bss/infra|ibss/adhoc] bss type to scan
        -b MAC, --bssid=MAC     particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
        -n N, --nprobes=N       number of probes per scanned channel
        -a N, --active=N        dwell time per channel for active scanning
        -p N, --passive=N       dwell time per channel for passive scanning
        -h N, --home=N          dwell time for the home channel between channel scans
        -c L, --channels=L      comma or space separated list of channels to scan

passive Puts scan engine into passive mode

regulatory
        Get/Set regulatory domain mode (802.11d). Driver must be down.

spect   Get/Set 802.11h Spectrum Management mode.
        0 - Off
        1 - Loose interpretation of 11h spec - may join non-11h APs
        2 - Strict interpretation of 11h spec - may not join non-11h APs
        3 - Disable 11h and enable 11d
        4 - Loose interpretation of 11h+d spec - may join non-11h APs

scanresults
        Return results from last scan.

iscanresults
        Return results from last iscan. Specify a buflen (max 8188)
        to artificially limit the size of the results buffer.
        iscanresults [buflen]


assoc   Print information about current network association.
        (also known as "status")

status  Print information about current network association.
        (also known as "assoc")

disassoc
        Disassociate from the current BSS/IBSS.

chanlist
        Deprecated. Use channels.

channels
        Return valid channels for the current settings.

channels_in_country
        Return valid channels for the country specified.
        Arg 1 is the country abbreviation
        Arg 2 is the band(a or b)

curpower
        Return current tx power settings.
        -q (quiet): estimated power only.

txinstpwr
        Return tx power based on instant TSSI

scansuppress
        Suppress all scans for testing.
        0 - allow scans
        1 - suppress scans

evm     Start an EVM test on the given channel, or stop EVM test.
        Arg 1 is channel number 1-14, or "off" or 0 to stop the test.
        Arg 2 is optional rate (1, 2, 5.5 or 11)

rateset Returns or sets the supported and basic rateset, (b) indicates basic
        With no args, returns the rateset. Args are
        rateset "default" | "all" | <arbitrary rateset>
                default - driver defaults
                all - all rates are basic rates
                arbitrary rateset - list of rates
        List of rates are in Mbps and each rate is optionally followed
        by "(b)" or "b" for a Basic rate. Example: 1(b) 2b 5.5 11
        At least one rate must be Basic for a legal rateset.

roam_trigger
        Get or Set the roam trigger RSSI threshold:
        Get: roam_trigger [a|b]
        Set: roam_trigger <integer> [a|b|all]
        integer -   0: default
                    1: optimize bandwidth
                    2: optimize distance
            [-1, -99]: dBm trigger value

roam_delta
        Set the roam candidate qualification delta. roam_delta [integer [, a/b]]

roam_scan_period
        Set the roam candidate qualification delta.  (integer)

suprates
        Returns or sets the 11g override for the supported rateset
        With no args, returns the rateset. Args are a list of rates,
        or 0 or -1 to specify an empty rateset to clear the override.
        List of rates are in Mbps, example: 1 2 5.5 11

scan_channel_time
        Get/Set scan channel time

scan_unassoc_time
        Get/Set unassociated scan channel dwell time

scan_home_time
        Get/Set scan home channel dwell time

scan_passive_time
        Get/Set passive scan channel dwell time

scan_nprobes
        Get/Set scan parameter for number of probes to use per channel scanned

prb_resp_timeout
        Get/Set probe response timeout

channel_qa
        Get last channel quality measurment

channel_qa_start
        Start a channel quality measurment

country Select Country Code for driver operational region
        Use either long name or abbreviation from ISO 3166.
        Use 'wl country list [band(a or b)]' for the list of supported countries

autocountry_default
        Select Country Code for use with Auto Contry Discovery

join    Join a specified network SSID.
        Join syntax is: join <ssid> [key xxxxx] [imode bss|ibss] [amode open|shared|wpa|wpapsk|wpa2|wpa2psk|wpanone]

ssid    Set or get a configuration's SSID.
        wl ssid [-C num]|[--cfg=num] [<ssid>]
        If the configuration index 'num' is not given, configuraion #0 is assumed and
        setting will initiate an assoication attempt if in infrastructure mode,
        or join/creation of an IBSS if in IBSS mode,
        or creation of a BSS if in AP mode.

mac     Set or get the list of source MAC address matches.
        wl mac xx:xx:xx:xx:xx:xx [xx:xx:xx:xx:xx:xx ...]
        To Clear the list: wl mac none

macmode Set the mode of the MAC list.
        0 - Disable MAC address matching.
        1 - Deny association to stations on the MAC list.
        2 - Allow association to stations on the MAC list.

wds     Set or get the list of WDS member MAC addresses.
        Set using a space separated list of MAC addresses.
         wl wds xx:xx:xx:xx:xx:xx [xx:xx:xx:xx:xx:xx ...]

lazywds Set or get "lazy" WDS mode (dynamically grant WDS membership to anyone).

noise   Get noise (moving average) right after tx in dBm

fqacurcy
        Manufacturing test: set frequency accuracy mode.
        freqacuracy syntax is: fqacurcy <channel>
        Arg is channel number 1-14, or 0 to stop the test.

crsuprs Manufacturing test: set carrier suppression mode.
        carriersuprs syntax is: crsuprs <channel>
        Arg is channel number 1-14, or 0 to stop the test.

longtrain
        Manufacturing test: set longtraining mode.
        longtrain syntax is: longtrain <channel>
        Arg is A band channel number or 0 to stop the test.

band    Returns or sets the current band
        auto - auto switch between available bands (default)
        a - force use of 802.11a band
        b - force use of 802.11b band

bands   Return the list of available 802.11 bands

phylist Return the list of available phytypes

shortslot
        Get current 11g Short Slot Timing mode. (0=long, 1=short)

shortslot_override
        Get/Set 11g Short Slot Timing mode override. (-1=auto, 0=long, 1=short)

shortslot_restrict
        Get/Set AP Restriction on associations for 11g Short Slot Timing capable STAs.
        0 - Do not restrict association based on ShortSlot capability
        1 - Restrict association to STAs with ShortSlot capability

ignore_bcns
        AP only (G mode): Check for beacons without NONERP element(0=Examine beacons, 1=Ignore beacons)

pktcnt  Get the summary of good and bad packets.

upgrade Upgrade the firmware on an embedded device

gmode   Set the 54g Mode (LegacyB|Auto||GOnly|BDeferred|Performance|LRS)

gmode_protection
        Get G protection mode. (0=disabled, 1=enabled)

gmode_protection_control
        Get/Set 11g protection mode control alg.(0=always off, 1=monitor local association, 2=monitor overlapping BSS)

gmode_protection_override
        Get/Set 11g protection mode override. (-1=auto, 0=disable, 1=enable)

protection_control
        Get/Set protection mode control alg.(0=always off, 1=monitor local association, 2=monitor overlapping BSS)

legacy_erp
        Get/Set 11g legacy ERP inclusion (0=disable, 1=enable)

scb_timeout
        AP only: inactivity timeout value for authenticated stas

assoclist
        AP only: Get the list of associated MAC addresses.

isup    Get driver operational state (0=down, 1=up)

rssi    Get the current RSSI val, for an AP you must specify the mac addr of the STA

phy_rssi_ant
        Get RSSI per antenna (only support NPHY now)


fasttimer
        Deprecated. Use fast_timer.

slowtimer
        Deprecated. Use slow_timer.

glacialtimer
        Deprecated. Use glacial_timer.

radar   Enable/Disable radar

radarargs
        Get/Set Radar parameters in
        order as npulses, ncontig, min_pw , max_pw, thresh0, thresh1, blank,
        fmdemodcfg, tnpulses_lp, min_pw_lp, max_pw_lp, min_fm_lp,
        max_deltat_lp, min_deltat, max_deltat


radarargs40
        Get/Set Radar parameters for 40Mhz channel in
        order as npulses, ncontig, min_pw , max_pw, thresh0, thresh1, blank,
        fmdemodcfg, tnpulses_lp, min_pw_lp, max_pw_lp, min_fm_lp,
        max_deltat_lp, min_deltat, max_deltat


dfs_status
        Get dfs status

interference
        Get/Set interference mitigation mode. Choices are:
        0 = none
        1 = non wlan
        2 = wlan manual
        3 = wlan automatic

frameburst
        Disable/Enable frameburst mode

pwr_percent
        Get/Set power output percentage

toe     Enable/Disable tcpip offload feature

toe_ol  Get/Set tcpip offload components

toe_stats
        Display checksum offload statistics

toe_stats_clear
        Clear checksum offload statistics

arpoe   Enable/Disable arp agent offload feature

arp_ol  Get/Set arp offload components

arp_peerage
        Get/Set age of the arp entry in minutes

arp_table_clear
        Clear arp cache

arp_hostip
        Add a host-ip address or display them

arp_hostip_clear
        Clear all host-ip addresses

arp_stats
        Display ARP offload statistics

arp_stats_clear
        Clear ARP offload statistics

wet     Get/Set wireless ethernet bridging mode

bi      Get/Set the beacon period (bi=beacon interval)

dtim    Get/Set DTIM

wds_remote_mac
        Get WDS link remote endpoint's MAC address

wds_wpa_role_old
        Get WDS link local endpoint's WPA role (old)

wds_wpa_role
        Get/Set WDS link local endpoint's WPA role

authe_sta_list
        Get authenticated sta mac address list

autho_sta_list
        Get authorized sta mac address list

measure_req
        Send an 802.11h measurement request.
        Usage: wl measure_req <type> <target MAC addr>
        Measurement types are: TPC, Basic, CCA, RPI
        Target MAC addr format is xx:xx:xx:xx:xx:xx

quiet   Send an 802.11h quiet command.
        Usage: wl quiet <TBTTs until start>, <duration (in TUs)>, <offset (in TUs)>

csa     Send an 802.11h channel switch anouncement with chanspec:
        <mode> <count> <channel>[a,b][n][u,l]
        mode (0 or 1)
        count (0-254)
        channel number (0-224)
        band a=5G, b=2G
        bandwidth n=10, non for 20 & 40
        ctl sideband, l=lower, u=upper, default no ctl sideband


constraint
        Send an 802.11h Power Constraint IE
        Usage: wl constraint 1-255 db

rm_req  Request a radio measurement of type basic, cca, or rpi
        specify a series of measurement types each followed by options.
        example: wl rm_req cca -c 1 -d 50 cca -c 6 cca -c 11
        Options:
        -t n  numeric token id for measurement set or measurement
        -c n  channel
        -d n  duration in TUs (1024 us)
        -p    parallel flag, measurement starts at the same time as previous

        Each measurement specified uses the same channel and duration as the
        previous unless a new channel or duration is specified.

rm_rep  Get current radio measurement report

join_pref
        Set/Get join target preferences.

assoc_pref
        Set/Get association preference.
Usage: wl assoc_pref [auto|a|b|g]

wme     Set WME (Wireless Multimedia Extensions) mode (0=off, 1=on, -1=auto)

wme_ac  wl wme_ac ap|sta [be|bk|vi|vo [ecwmax|ecwmin|txop|aifsn|acm <value>] ...]

wme_apsd
        Set APSD (Automatic Power Save Delivery) mode on AP (0=off, 1=on)

wme_apsd_sta
        Set APSD parameters on STA. Driver must be down.
Usage: wl wme_apsd_sta <max_sp_len> <be> <bk> <vi> <vo>
   <max_sp_len>: number of frames per USP: 0 (all), 2, 4, or 6
   <xx>: value 0 to disable, 1 to enable U-APSD per AC

wme_dp  Set AC queue discard policy.
Usage: wl wme_dp <be> <bk> <vi> <vo>
   <xx>: value 0 for newest-first, 1 for oldest-first

wme_counters
        print WMM stats

wme_clear_counters
        clear WMM counters

wme_tx_params
        wl wme_tx_params [be|bk|vi|vo [short|sfb|long|lfb|max_rate <value>] ...]

lifetime
        Set Lifetime parameter (milliseconds) for each ac.
wl lifetime be|bk|vi|vo [<value>]

reinit  Reinitialize device

sta_info
        wl sta_info <xx:xx:xx:xx:xx:xx>

nphy_test_tssi
        wl nphy_test_tssi val

nphy_test_tssi_offs
        wl nphy_test_tssi_offs val

nphy_rssiant
        wl nphy_rssiant antindex(0-3)

cap     driver capabilities

malloc_dump
        Deprecated. Folded under 'wl dump malloc

chan_info
        channel info

add_ie  Add a vendor proprietary IE to 802.11 management packets
Usage: wl add_ie <pktflag> length OUI hexdata
<pktflag>: Bit 0 - Beacons
           Bit 1 - Probe Rsp
           Bit 2 - Assoc/Reassoc Rsp
           Bit 3 - Auth Rsp
           Bit 4 - Probe Req
           Bit 5 - Assoc/Reassoc Req
Example: wl add_ie 3 10 00:90:4C 0101050c121a03
         to add this IE to beacons and probe responses

del_ie  Delete a vendor proprietary IE from 802.11 management packets
Usage: wl del_ie <pktflag> length OUI hexdata
<pktflag>: Bit 0 - Beacons
           Bit 1 - Probe Rsp
           Bit 2 - Assoc/Reassoc Rsp
           Bit 3 - Auth Rsp
           Bit 4 - Probe Req
           Bit 5 - Assoc/Reassoc Req
Example: wl del_ie 3 10 00:90:4C 0101050c121a03

list_ie Dump the list of vendor proprietary IEs

rand    Get a 2-byte Random Number from the MAC's PRNG
Usage: wl rand

otpw    Write an srom image to on-chip otp
Usage: wl otpw file

nvotpw  Write nvram to on-chip otp
Usage: wl nvotpw file

bcmerrorstr
        errorstring

freqtrack
        Set Frequency Tracking Mode (0=Auto, 1=On, 2=OFF)

eventing
        set/get 128-bit hex filter bitmask for MAC event reporting up to application layer

event_msgs
        set/get 128-bit hex filter bitmask for MAC event reporting via packet indications

counters
        Return driver counter values

assoc_info
        Returns the assoc req and resp information [STA only]

autochannel
        auto channel selection:
        1 to issue a channel scanning;
        2 to set channel based on the channel scanning result;
        without argument to only show the channel selected;
        ssid must set to null before this process, RF must be up

csscantimer
        auto channel scan timer in minutes (0 to disable)

closed  hides the network from active scans, 0 or 1.
        0 is open, 1 is hide

pmkid_info
        Returns the pmkid table

abminrate
        get/set afterburner minimum rate threshold

bss     set/get BSS enabled status: up/down

closednet
        set/get BSS closed network attribute

ap_isolate
        set/get AP isolation

eap_restrict
        set/get EAP restriction

diag    diag testindex(1-interrupt, 2-loopback, 3-memory, 4-led); precede by 'wl down' and follow by 'wl up'

reset_d11cnts
        reset 802.11 MIB counters

staname get/set station name:
        Maximum name length is 15 bytes

apname  get AP name

otpdump Dump raw otp

nrate   -r legacy rate (CCK, OFDM)-m mcs index-s stf mode (0=SISO,1=CDD,2=STBC(not supported),3=SDM)

mimo_txbw
        get/set mimo txbw (2=20Mhz(lower), 3=20Mhz upper, 4=40Mhz, 5=40Mhz dup<mcs32 only)

cac_addts
        add TSPEC, error if STA is not associated or WME is not enabled
        arg1: G711, signal, or starting TSPEC parameter input list
        arg2: direction for G711 and signal(bi-direction by default):
                 1: uplink direction
                 2: downlink direction

cac_delts
        delete TSPEC, error if STA is not associated or WME is not enabled
        arg1: G711, signal, or starting TSPEC parameter input list
        arg2: direction for G711 and signal(bi-direction by default):
                 1: uplink direction
                 2: downlink direction

cac_tslist
        Get the list of TSINFO in driver
        eg. 'wl cac_tslist' get a list of TSINFO

cac_tspec
        Get specific TSPEC with matching TSINFO
        eg. 'wl cac_tspec 0xaa 0xbb 0xcc' where 0xaa 0xbb & 0xcc are TSINFO octets

nphy_caldump
        Dump the NPHY calibration coefficients

nphy_antsel
        get/set antenna configuration
        set: -1(AUTO), 0xAB(fixed antenna selection)
                where A and B is the antenna numbers used for RF chain 0 and 1 respectively
        query: <utx>[AUTO] <urx>[AUTO] <dtx>[AUTO] <drx>[AUTO]
                where utx = TX unicast antenna configuration
                        urx = RX unicast antenna configuration
                        dtx = TX default (non-unicast) antenna configuration
                        drx = RX default (non-unicast) antenna configuration


txfifo_sz
        set/get the txfifo size; usage: wl txfifo_sz <fifonum> <size_in_bytes>

phy_rxiqest
        Get phy RX IQ noise in dBm:
        -s # of samples (2^n)
        -a antenna select, 0,1 or 3


rifs    set/get the rifs status; usage: wl rifs <1/0> (On/Off)


pkteng_start
        start packet engine; usage: wl pkteng_start <xx:xx:xx:xx:xx:xx> <tx|rx> [ipg] [len] [nframes] [src]
        ipg: inter packet gap in us
        len: packet length
        nframes: number of frames; 0 indicates continuous tx test


pkteng_stop
        stop packet engine; usage: wl pkteng_stop <tx|rx>

pkteng_stats
        packet engine stats; usage: wl pkteng_stats

wowl    Enable/disable WOWL events
  0   - Clear all events
Bit 0 - Wakeup on Magic Packet
Bit 1 - Wakeup on NetPattern (use 'wl wowl_pattern' to configure pattern)
Bit 2 - Wakeup on loss-of-link due to Disassociation/Deauth
Bit 3 - Wakeup on retrograde tsf
Bit 4 - Wakeup on loss of beacon (use 'wl wowl_bcn_loss' to configure time)


wowl_bcn_loss
        Set #of seconds of beacon loss for wakeup event


wowl_pattern
        usage: wowl_pattern [ [ add | del ] offset mask value ]
No options -- lists existing pattern list
add -- Adds the pattern to the list
del -- Removes a pattern from the list
offset -- Starting offset for the pattern
mask -- Mask to be used for pattern. Bit i of mask => byte i of the pattern
value -- Value of the pattern


wowl_wakeind
        usage: wowl_wakeind [clear]
Shows last system wakeup event indications from PCI and D11 cores
clear - Clear the indications


wowl_pkt
        Send a wakeup frame to wakup a sleeping STA in WAKE mode
Usage: wl wowl_pkt <len> <dst ea> [ magic <STA ea> | net <offset> <pattern>]
e.g. To send bcast magic frame -- wl wowl_pkt 102 ff:ff:ff:ff:ff:ff magic 00:90:4c:AA:BB:CC
     To send ucast magic frame -- wl wowl_pkt 102 00:90:4c:aa:bb:cc magic 00:90:4c:AA:BB:CC
     To send a frame with L2 unicast - wl wowl_pkt 102 00:90:4c:aa:bb:cc net 0 0x00904caabbcc
 NOTE: offset for netpattern frame starts from "Dest EA" of ethernet frame.So dest ea will be used only when offset is >= 6


wme_apsd_trigger
        Set Periodic APSD Trigger Frame Timer timeout in ms (0=off)

wme_autotrigger
        Enable/Disable sending of APSD Trigger frame when all ac are delivery enabled

reassoc Initiate an extended (re)association request.
        Default active scan across all channels for any SSID.
        Optional args: BSSID and list of channels to scan.
        Options:
        -b -BSSID=xx:xx:xx:xx:xx:xx,            BSSID to scan and join
        -c L, --channels=L      comma or space separated list of channels to search in  -r --radioband (5(a) or 2(b/g))
        -w --bandwidth, 10,20 or 40
        -s ctl sideband, -1=lower, 0=none, 1=upper

send_nulldata
        Sed a null frame to the specified hw address

assoclistinfo
        AP only: Get the list of yet another form of associated station info

led     Wileless LED
Usage: wl led pin func polarity
        func selection:
        2  - activity
        4  - A radio
        5  - B radio
        32 - off
        33 - blink slow
        34 - blink medium
        35 - blink fast
        36 - on
Example: wl led 0 2 1


# nvram_dump
nvram_dump: not found
#
# wlctl nvram_dump
manfid=0x2d0
prodid=0x4ae
sdmaxblk0=1
sdmaxspeed=50000
manf=Broadcom
productname=802.11b/g SDIO
sromrev=3
vendid=0x14e4
devid=0x4315
boardtype=0x4ae
boardrev=0x11
boardflags=0x60e00
xtalfreq=20000
opo=0
pa0b0=6369
pa0b1=64494
pa0b2=65350
pa0itssit=62
pa0maxpwr=66
aa2g=3
ag0=2
tri2g=94
rxpo2g=246
rssismf2g=15
rssismc2g=0
rssisav2g=2
bxa2g=0
ccode=
cctl=0x0
boardnum=6
macaddr=00:90:4c:df:00:06